...
- Select an Edge Site MTN1 (or MTN2) by clicking on the radio button in the GUI table displayed in the Home page. These are the two default sites available in the Seed code.
- For the selected Edge site, select a Blueprint (Rover or Unicycle) from the drop-down menu.
- Click on Upload button (in the Blueprint column), this will open a pop-up dialog
- Provide the edge site-specific details such as:
- Host IP address
- Host user
- Host password.
Click on Browse button, select the input file for Blueprint - Rover (Single-Node Cluster).
The input file is a property file that stores information inkey-value
format. Sample input file used for ‘Rover’ deploy:Info Copy and paste the below contents in to a file, and save it as rover.txt. Use this file for uploading as mentioned in step 4.d above.
Verify the configuration details as applicable to your environment. For more details refer to Appendix - Edge Site Configuration
Code Block language text title rover.txt # Copyright 2018 AT&T Intellectual Property. All other rights reserved. # # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. # host name for server SRV_NAME=aknode42 # out of band interface information for server (idrac/ilo/etc) SRV_OOB_IP=192.168.41.42 SRV_OOB_USR=root SRV_OOB_PWD=calvin # server oem - Dell or HPE (case sensitive) SRV_OEM=Dell # name of network interface used during build when "ipxe.efi" is booted and when OS is booted # ipxe numbers interfaces from 0-n in pci bus order. # the netX value will depend on how many nics are in the server # and which pci device number is assigned to the slot SRV_IPXE_INF=net4 SRV_BLD_INF=enp94s0f0 SRV_BOOT_DEVICE=sdg # ipxe script to use - based on the os version and kernel to install # valid options are script-hwe-16.04.5-amd64.ipxe or script-16.04.5-amd64.ipxe SRV_BLD_SCRIPT=script-hwe-16.04.5-amd64.ipxe # template xml file to set bios and raid configuration settings SRV_BIOS_TEMPLATE=dell_r740_g14_uefi_base.xml.template SRV_BOOT_TEMPLATE=dell_r740_g14_uefi_httpboot.xml.template SRV_HTTP_BOOT_DEV=NIC.Slot.7-1-1 # tempalte to run to configure OS after first boot # current options are: firstboot.sh.template, firstboot-genesis.sh.template or firstboot-airship-iab.sh.template SRV_FIRSTBOOT_TEMPLATE=firstboot-airship-iab.sh.template # VLAN to use during build and for final network configuration SRV_VLAN=41 # basic network information for dhcp config and final server network settings SRV_MTU=9000 SRV_IP=192.168.2.42 SRV_SUBNET=192.168.2.0 SRV_NETMASK=255.255.255.0 SRV_GATEWAY=192.168.2.200 SRV_DNS=192.168.2.85 SRV_DOMAIN=lab.akraino.org SRV_DNSSEARCH=lab.akraino.org SRV_NTP=ntp.ubuntu.org # root password for server being built SRV_PWD=akraino,d # network bond information SRV_BOND=bond0 SRV_SLAVE1=enp94s0f0 SRV_SLAVE2=enp94s0f1
...