Versions Compared

Old Version 43

changes.mady.by.user James Williams

Saved on

compared with

New Version 44

changes.mady.by.user James Williams

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  1. Select an Edge Site MTN1 or MTN2 (these are the two default lab sites hosted in middle town NJ) by clicking on radio button provided in the first column of the table.
  2. For the selected Edge Site, select a Rover Blueprint from the drop-down menu.
  3. Click on Upload button (in the Sites column), this will open a pop-up dialog
  4. Provide the edge site-specific details such as:
    1. Host IP address

    2. Host username

    3. Host password.

  5. Click on Browse button, select the input file for Blueprint - Rover (Single-Node Cluster). 
    The input file is a property file that stores information in key-value format.  Sample input file used for ‘Rover’ deploy: 

    Info

    Copy and paste the below contents in to a file, and save it as rover.txt. Use this file for uploading as mentioned in step 4.d above.

    Verify the configuration details as applicable to your environment. For more details refer to Appendix - Edge Site Configuration


    Code Block
    languagetext
    titlerover.txt
    # Copyright 2018 AT&T Intellectual Property.  All other rights reserved.
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
# Add proxy settings if required for your environment
# export http_proxy=http://your.proxy.com:8080/
# export https_proxy=http://your.proxy.com:8080/
#
# host name for server
SRV_NAME=aknode44aknode45
# server oem - Dell or HPE (case sensitive)
SRV_OEM=Dell
# out of band interface information for server (idrac/ilo/etc)
SRV_OOB_IP=192.168.41.4445
SRV_OOB_USR=root
SRV_OOB_PWD=calvin
# mac address of server to be used during the build - not required for Dell servers
# SRV_MAC=3c:fd:fe:b8:10:60
# name of network interface used during build when ipxe.efi is booted and when os is booted
# ipxe numbers ports from 0-n in pci bus order.
# the netx value will depend on how many nics are in the server
# and which pci device number is assigned to the slot
SRV_IPXE_INF=net8
# the build interface is the nic used by the Ubuntu installed to load the OS
SRV_BLD_INF=enp135s0f0
# the boot device is the device name on which the OS will be loaded
SRV_BOOT_DEVICE=sdg
# ipxe script to use - based on the os version and kernel to install
# valid options are script-hwe-16.04.5-amd64.ipxe or script-16.04.5-amd64.ipxe
SRV_BLD_SCRIPT=script-hwe-16.04.5-amd64.ipxe
# template xml file to set bios and raid configuration settings
SRV_BIOS_TEMPLATE=dell_r740_g14_uefi_base.xml.template
SRV_BOOT_TEMPLATE=dell_r740_g14_uefi_httpboot.xml.template
SRV_HTTP_BOOT_DEV=NIC.Slot.7-1-1
# tempalte to run to configure OS after first boot
# current options are: firstboot.sh.template, firstboot-genesis.sh.tempate or firstboot-airship-iab.sh.template
SRV_FIRSTBOOT_TEMPLATE=firstboot.sh.template
# VLAN to use during build and for final network configuration
SRV_VLAN=41
# basic network information for dhcp config and final server network settings
SRV_MTU=9000
SRV_IP=192.168.2.4445
SRV_SUBNET=192.168.2.0
SRV_NETMASK=255.255.255.0
SRV_GATEWAY=192.168.2.200
SRV_DNS=192.168.2.85
SRV_DOMAIN=lab.akraino.org
SRV_DNSSEARCH=lab.akraino.org
SRV_NTP=ntp.ubuntu.org
# root password for server being built
SRV_PWD=akraino,d
# network bond information
SRV_BOND=bond0
SRV_SLAVE1=enp135s0f0
SRV_SLAVE2=enp135s0f1

...