Skip to end of metadata
Go to start of metadata

Introduction

This document outlines the steps to deploy SDN-Enabled Broadband Access (SEBA) for Telco Appliance.  With the exception of the installation of the SEBA application components (VOLTHA, NEM, ONOS), the installation process follows that of REC (REC Installation Guide).  The production deployment of SEBA is intended to be done using the Akraino Regional Controller, but this release focuses on deploying SEBA without the Regional Controller.  Instructions on how to deploy the SEBA blueprint using the Regional Controller will be covered in a future release.

The instructions below directly invoke the SEBA Deployer from the BMC, iLO or iDRAC of a physical server. The basic workflow of the SEBA deployer is to copy a base image to the first controller in the cluster and then read the contents of a configuration file (typically called user_config.yaml) to deploy the base OS and all additional software to the rest of the nodes in the cluster.

An overview and diagram of the network connectivity is available on the Radio Edge Cloud Validation Lab page.

Pre-Installation Requirements for SEBA Cluster

Hardware Requirements:

SEBA is a fully integrated stack from the hardware up to and including the application, so for best results it is necessary to use one of the tested hardware configurations. Although SEBA is intended to run on a variety of different hardware platforms, it includes a hardware detector component that customizes each installation based on the hardware present and will need (possibly minor) changes to run on additional hardware configurations. The primary focus of Akraino Release 2 self-certification testing for the SEBA blueprint is the Nokia Open Edge servers, so some issues may be encountered with other server types.

  • Minimum of 3 nodes.
  • Total Physical Compute Cores:  60 (120 vCPUs)
  • Total Physical Compute Memory:  192GB minimum per node
  • Total SSD-based OS Storage:  2.8 TB (6 x 480GB SSDs)
  • Total Application-based Raw Storage:  5.7 TB (6 x 960GB SSDs)
  • Networking Per Server:     Apps - 2 x 25GbE (per Server) and DCIM - 2 x 10GbE + 1 1Gbt (shared)                                        

The specific recommended configuration as of the Release 2 time frame is the Open Edge configuration for a single cluster documented in the Radio Edge Cloud Validation Lab, with only three server blades populated (instead of five server blades for REC).

BIOS Requirements:

  • BIOS set to Legacy (Not UEFI)
  • CPU Configuration/Turbo Mode Disabled
  • Virtualization Enabled
  • IPMI Enabled
  • Boot Order set with Hard Disk listed as first in the list.

As of Akraino Release 2, the Telco Appliance blueprint family does not yet include automatic configuration for a pre-boot environment. The following versions were manually loaded on the Open Edge servers in the SEBA Blueprint Validation Lab (note:  this may be facilitated with the same script utilized by REC for Akraino Release 1).  In the future, automatic configuration of the pre-boot environment is expected to be a function of the Regional Controller under the direction of the SEBA pod create workflow script.

  • BIOS1: 3B06
  • BMC1: 3.13.00
  • BMC2: 3.08.00
  • CPLD: 0x01

Network Requirements:

The SEBA cluster requires the following segmented (VLAN), routed networks accessible by all nodes in the cluster:

  • External Operations, Administration and Management (OAM) Network
  • Out Of Band (OOB) (iLO/iDRAC) network(s)
  • Storage/Ceph network(s)
  • Internal network for Kubernetes connectivity
  • NTP and DNS accessibility

The SEBA installer will configure NTP and DNS using the parameters entered in the user_config.yaml.  However, the network must be configured for the SEBA cluster to be able to access the NTP and DNS servers prior to the install.

About user_config.yaml

The user_config.yaml file contains details for your SEBA cluster such as required network CIDRs, usernames, passwords, DNS and NTP server ip addresses, etc.  The SEBA configuration is flexible, but there are dependencies: e.g., using DPDK requires a networking profile with ovs-dpdk type, a performance profile with CPU pinning & hugepages and performance profile links on the compute node(s).  All values in the user_config.yaml should be updated to match the environment for your deployment.

The following link points to the latest user_config template with descriptions and examples for every available parameter:  user_config.yaml template


Note: the version number listed in the user_config.yaml needs to follow closely the version from the template. There is a strict version checking during deployment for the first two part of the version number. The following rules apply to the yaml's version parameter:

### Version numbering:
###    X.0.0
###        - Major structural changes compared to the previous version.
###        - Requires all users to update their user configuration to
###          the new template
###    a.X.0
###        - Significant changes in the template within current structure
###          (e.g. new mandatory attributes)
###        - Requires all users to update their user configuration according
###          to the new template (e.g. add new mandatory attributes)
###    a.b.X
###        - Minor changes in template (e.g. new optional attributes or
###          changes in possible values, value ranges or default values)
###        - Backwards compatible

Example user_config.yaml

user_config.yaml
---
version: 2.0.0
name: seba-foundry

description: SEBA Deployment on OpenEdge

time:
    ntp_servers: [216.239.35.4, 216.239.35.5]
    zone: America/New_York

users:
    admin_user_name: cloudadmin
    admin_user_password: "$6$XXXXXXX$C3fvJHW8o1383ZTb.vQ86wfjK7VxI7N7KwE0PxQrPdDRpotJMY8wcB2XHUQCheuHf44KGrg.AMGoI3d37IHua/"
    initial_user_name: myadmin
    initial_user_password: XXXXXXXX
    admin_password: XXXXXXXX

networking:
    dns: [ 8.8.8.8, 8.8.4.4 ]
    mtu: 9000
    infra_external:
        mtu: 1500
        network_domains:
            rack-1:
                cidr: 10.65.1.0/24
                gateway: 10.65.1.1
                vlan: 751
                ip_range_start: 10.65.1.50
                ip_range_end: 10.65.1.60
                #routes:
                #    - {to: 10.99.99.0/24, via: 10.65.1.250}
    infra_storage_cluster:
        network_domains:
            rack-1:
                cidr: 192.168.11.0/24
                ip_range_start: 192.168.11.51
                ip_range_end: 192.168.11.60
                vlan: 3911
    infra_internal:
        network_domains:
            rack-1:
                cidr: 192.168.12.0/24
                ip_range_start: 192.168.12.51
                ip_range_end: 192.168.12.60
                vlan: 3912

caas:
    docker_size_quota: 2G
    helm_operation_timeout: 900
    docker0_cidr: 172.17.0.1/16
    instantiation_timeout: 60
    helm_parameters: { "registry_url": "registry.kube-system.svc.nokia.net" }
    encrypted_ca: ["U2FsdGVkX1+iaWyYk3W01IFpfVdughR5aDKo2NpcBw2UStYnepHlr5IJD3euo1lS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\n8UyCKFyyPCj5OwVbwGSgQg=="]
    encrypted_ca_key: ["U2FsdGVkX1+WlNST+WkysFUHYAPfViWe01tCCQsXPsWsUskB4oNNC78bXdEv33+3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\njJu5IidT3u5+hUlIdZtEtA=="]

storage:
    backends:
        lvm:
            enabled: false
        ceph:
            osd_pool_default_size: 2
            enabled: true

network_profiles:
    controller_network:
        linux_bonding_options: "mode=lacp"
        ovs_bonding_options: "mode=lacp"

        bonding_interfaces:
            bond0: [ens11f0,ens11f1]

        interface_net_mapping:
            bond0: [infra_internal, infra_external, infra_storage_cluster]

performance_profiles:
    caas_cpu_profile:
        caas_cpu_pools:
            exclusive_pool_percentage: 25
            shared_pool_percentage: 75

storage_profiles:
    caas_worker_docker_profile:
        lvm_instance_storage_partitions: ["1"]
        mount_dir: /var/lib/docker
        mount_options: noatime,nodiratime,logbufs=8,pquota
        backend: bare_lvm
        lv_name: docker

    ceph_backend_profile:
        backend: ceph
        nr_of_ceph_osd_disks: 2
        ceph_pg_openstack_caas_share_ratio: "0:1"

hosts:
    controller-1:
        service_profiles:     [ caas_master, storage ]
        network_profiles:     [ controller_network ]
        storage_profiles:     [ ceph_backend_profile ]
        performance_profiles: [ caas_cpu_profile ]
        network_domain: rack-1
        hwmgmt:
            address:  10.65.3.57
            user:     admin
            password: XXXXXXXX
    controller-2:
        service_profiles:     [ caas_master, storage ]
        network_profiles:     [ controller_network ]
        storage_profiles:     [ ceph_backend_profile ]
        performance_profiles: [ caas_cpu_profile ]
        network_domain: rack-1
        hwmgmt:
            address:  10.65.3.56
            user:     admin
            password: XXXXXXXX
    controller-3:
        service_profiles:     [ caas_master, storage ]
        network_profiles:     [ controller_network ]
        storage_profiles:     [ ceph_backend_profile ]
        performance_profiles: [ caas_cpu_profile ]
        network_domain: rack-1
        hwmgmt:
            address:  10.65.3.55
            user:     admin
            password: XXXXXXXX

host_os:
    lockout_time: 300
    failed_login_attempts: 5
...


YAML Requirements

  • The YAML files need to edited/created using Linux editors or in Windows Notepad++
  • YAML files do not support TABS.  You must space over to the location for the text.

Note:  You have a better chance at creating a working YAML by editing an existing file or using the template rather than starting from scratch.

Installing SEBA

Obtaining the ISO Image

Recent builds can be obtained from the Akraino Nexus server. Choose either "latest" or a specific build number from the release images directory and download the file install.iso. Build number 185 is the Akraino Release 1 image from the 4th of October, 2019 and was used for the initial validation of the SEBA blueprint.  Options for booting the ISO on your target hardware include NFS, HTTP, or USB memory stick. You must place the ISO in a suitable location (e.g., NFS server, HTTP(S) server or USB memory stick) before starting the boot process. The file bootcd.iso, which is also in the same directory, is used only when deploying via the Akraino Regional Controller using the Telco Appliance Remote Installer. You can ignore bootcd.iso when following the manual procedure below.

Accessing REC.ISO

Nokia OpenEdge Servers

Login to the controller-1 BMC ip using a web browser (https://xxx.xxx.xxx.xxx).

Go to Settings/Media Redirection/General Settings.

Select the Remote Media Support.

Select the Mount CD/DVD.

Type the NFS server IP address.

Type the NFS share path.

Select the nfs in Share Type for CD/DVD.

Click Save.

Click OK to restart the VMedia Service.

Go to Settings/Media Redirection/Remote Images.

Select the image for the first CD/DVD device from the drop-down list.

Click the play button to map the image with the server’s CD/DVD devices. The Redirection Status changes to Started when the image redirection succeeds.

Go to Control & Maintain/Remote Control to open the Remote Console.

Reset the server.

Press F11 to boot menu and select boot from CD/DVD device.

HP Servers

(Future)

Dell Servers

(Future)

Ampere Servers

(Future)

Marvell Servers

(Future)

After rebooting, the installation will bring up the Akraino Edge Stack screen.

The first step is to clean all the drives discovered before installing the ISO image.

Select, 0 Set external network at the Installation window, press OK.

Arrow down to and press the spacebar to select the network interface to be used for the external network

 If using bonded nics, select the first interface in the bond.

Enter the external ip address with CIDR for controller-1:  172.28.15.211/24

Enter the gateway ip address for the external ip address just entered:   172.28.15.1

Enter the VLAN number:  141

The installation will check the link and connectivity of the IP addresses entered.

If the connectivity test passed, then Installation window will return. 

Uploading user_config.yaml

Go to your RC or jump server and scp (or sftp) your user_config.yaml to controller-1’s /etc/userconfig directory.

initial credentials: root/root.

scp user_config.yaml root@<controller-1 ip address>/etc/userconfig/


Select, 1 Start installation and OK.

After selecting Start Installation, the installation should start automatically, and the content of /srv/deployment/log/bootstrap.log should be displayed on the remote console.

Monitoring Deployment Progress/Status

You can monitor the SEBA deployment by checking the remote console screen or by tailing the logs on controller-1 node's /srv/deployment/log/ directory.

There are two log files:

bootstrap.log: deployment status log

cm.log: ansible execution log

tail -f /srv/deployment/log/cm.log

tail -f /srv/deployment/log/bootstrap.log

Note:  When the deployment to all the nodes has completed, “controller-1” will reboot automatically.

Verifying Deployment

A post-installation verification is required to ensure that all nodes and services were properly deployed.

You need to establish an ssh connection to the controller’s VIP address and login with administrative rights.

tail /srv/deployment/log/bootstrap.log

You should see: Installation complete, Installation Succeeded.

Go to SEBA Blueprint Test Document and follow the steps outlined there to ensure that all nodes and services were properly deployed.

Deployment Failures

Sometimes failures happen, usually due to misconfigurations or incorrect addresses.

To re-launch a failed deployment

There are two options for redeploying.  (Execute as root)

  1. /opt/cmframework/scripts/bootstrap.sh /etc/userconfig/user_config.yaml --install &
  2. openvt -s -w /opt/start-menu/start_menu.sh &

Note:  In some cases modifications to the user_config.yaml may be necessary to resolve a failure. 

If re-deployment is not possible, then the deployment will need to be started from booting to the REC.iso,

SEBA Installation onto REC cluster

Kubernetes 1.14 deprecates several legacy APIs and Kubernetes 1.16 disables them by default. For deployment of SEBA, it is necessary to manually enable these legacy Kubernetes APIs since they are not supported by Telco Appliance.  The deprecated APIs will be removed in Kubernetes 1.18.

The following commands will install the SEBA software on the cluster.

  • Enable legacy APIs by adding --runtime-config option to the command section of /etc/kubernetes/manifests/apiserver.yml on each node in the cluster.  Connect to each node using ssh and edit the file to match the example below.

    ssh cloudadmin@10.65.1.51
    sudo vi /etc/kubernetes/manifests/apiserver.yml
  • /etc/kubernetes/manifests/apiserver.yml
    ---
    apiVersion: v1
    kind: Pod
    metadata:
      name: kube-apiserver
      namespace: kube-system
    spec:
      hostNetwork: true
      containers:
        - name: kube-apiserver
          image: registry.kube-system.svc.rec.io:5555/caas/hyperkube:1.16.0-5
          securityContext:
            runAsUser: 144
          command:
            - "/kube-apiserver"
            - --admission-control=DefaultStorageClass,LimitRanger,MutatingAdmissionWebhook,NamespaceExists,NamespaceLifecycle,NodeRestriction,PodSecurityPolicy,ResourceQuota,ServiceAccount,ValidatingAdmissionWebhook
            - --advertise-address=192.168.12.51
            - --allow-privileged=true
            - --anonymous-auth=false
            - --apiserver-count=3
            - --audit-policy-file=/var/lib/caas/policies/audit-policy.yaml
            - --audit-log-format=json
            - --audit-log-maxsize=100
            - --audit-log-maxbackup=88
            - --audit-log-path=/var/log/audit/kube_apiserver/kube-apiserver-audit.log
            - --authorization-mode=Node,RBAC
            - --bind-address=192.168.12.51
            - --client-ca-file=/etc/openssl/ca.pem
            - --enable-bootstrap-token-auth=true
            - --etcd-cafile=/etc/etcd/ssl/ca.pem
            - --etcd-certfile=/etc/etcd/ssl/etcd1.pem
            - --etcd-keyfile=/etc/etcd/ssl/etcd1-key.pem
            - --etcd-servers=https://192.168.12.51:4111,https://192.168.12.52:4111,https://192.168.12.53:4111
            - --experimental-encryption-provider-config=/etc/kubernetes/ssl/secrets.conf
            - --feature-gates=SCTPSupport=True,CPUManager=False,TokenRequest=True,DevicePlugins=True
            - --insecure-port=0
            - --kubelet-certificate-authority=/etc/openssl/ca.pem
            - --kubelet-client-certificate=/etc/kubernetes/ssl/kubelet-server.pem
            - --kubelet-client-key=/etc/kubernetes/ssl/kubelet-server-key.pem
            - --kubelet-https=true
            - --max-requests-inflight=1000
            - --proxy-client-cert-file=/etc/kubernetes/ssl/metrics.crt
            - --proxy-client-key-file=/etc/kubernetes/ssl/metrics.key
            - --requestheader-client-ca-file=/etc/openssl/ca.pem
            - --requestheader-extra-headers-prefix=X-Remote-Extra-
            - --requestheader-group-headers=X-Remote-Group
            - --requestheader-username-headers=X-Remote-User
            - --secure-port=6443
            - --service-account-key-file=/etc/kubernetes/ssl/service-account.pem
            - --service-account-lookup=true
            - --service-cluster-ip-range=10.254.0.0/16
            - --tls-cert-file=/etc/kubernetes/ssl/tls-cert.pem
            - --tls-private-key-file=/etc/kubernetes/ssl/apiserver1-key.pem
            - --token-auth-file=/etc/kubernetes/ssl/tokens.csv
            - --runtime-config=apps/v1beta1=true,apps/v1beta2=true,extensions/v1beta1/daemonsets=true,extensions/v1beta1/deployments=true,extensions/v1beta1/replicasets=true,extensions/v1beta1/networkpolicies=true,extensions/v1beta1/podsecuritypolicies=true
    
          resources:
            requests:
              cpu: "50m"
          volumeMounts:
            - name: time-mount
              mountPath: /etc/localtime
              readOnly: true
            - name: secret-kubernetes
              mountPath: /etc/kubernetes/ssl
              readOnly: true
            - name: secret-root-ca
              mountPath: /etc/openssl/ca.pem
              readOnly: true
            - name: secret-etcd
              mountPath: /etc/etcd/ssl
              readOnly: true
            - name: audit-kube-apiserver
              mountPath: /var/log/audit/kube_apiserver/
              readOnly: false
            - name: audit-policy-dir
              mountPath: /var/lib/caas/policies
              readOnly: true
      volumes:
        - name: time-mount
          hostPath:
            path: /etc/localtime
        - name: secret-kubernetes
          hostPath:
            path: /etc/kubernetes/ssl
        - name: secret-root-ca
          hostPath:
            path: /etc/openssl/ca.pem
        - name: secret-etcd
          hostPath:
            path: /etc/etcd/ssl
        - name: audit-kube-apiserver
          hostPath:
            path: /var/log/audit/kube_apiserver/
        - name: audit-policy-dir
          hostPath:
            path: /var/lib/caas/policies
  • Connect to the first controller in the cluster to run the remaining commands.

    ssh cloudadmin@10.65.1.51
  • Delete the kube-apiserver pods and wait for the pods to be recreated.

    kubectl delete pod -n kube-system kube-apiserver-192.168.12.51
    kubectl delete pod -n kube-system kube-apiserver-192.168.12.52
    kubectl delete pod -n kube-system kube-apiserver-192.168.12.53
  • Add cluster-admin rights to to the tiller service account.

    kubectl create clusterrolebinding tiller-cluster-admin --clusterrole=cluster-admin --serviceaccount=kube-system:tiller
  • Add the CORD repository and updated indexes.

    helm repo add cord https://charts.opencord.org
    helm repo update
  • Install the CORD platform.

    helm install -n cord-platform --version 6.1.0 cord/cord-platform
  • Wait until all 3 etcd CRDs are present in Kubernetes

    kubectl get crd | grep -i etcd | wc -l
  • Install the SEBA profile.

    helm install -n seba --version 1.0.0 cord/seba
  • Install the AT&T workflow

    helm install -n att-workflow --version 1.0.2 cord/att-workflow
  • Wait for all pods to reach Completed or Running status.

    kubectl get pods
    Example output
    NAME                                                              READY   STATUS      RESTARTS   AGE     IP            NODE            NOMINATED NODE   READINESS GATES
    att-workflow-att-workflow-driver-6487d77db-rdwgk                  1/1     Running     0          2m1s    10.244.0.27   192.168.12.52   <none>           <none>
    att-workflow-tosca-loader-7btvq                                   0/1     Completed   4          2m1s    10.244.1.37   192.168.12.51   <none>           <none>
    cord-platform-etcd-operator-etcd-backup-operator-84dfbc689vqsj9   1/1     Running     0          4m9s    10.244.2.13   192.168.12.53   <none>           <none>
    cord-platform-etcd-operator-etcd-operator-8b6c64548-nnj2r         1/1     Running     0          4m9s    10.244.2.14   192.168.12.53   <none>           <none>
    cord-platform-etcd-operator-etcd-restore-operator-7f5f5b95sdxw5   1/1     Running     0          4m9s    10.244.0.13   192.168.12.52   <none>           <none>
    cord-platform-grafana-74c589b6db-jqnpv                            2/2     Running     0          4m9s    10.244.1.24   192.168.12.51   <none>           <none>
    cord-platform-kafka-0                                             1/1     Running     1          4m9s    10.244.1.25   192.168.12.51   <none>           <none>
    cord-platform-kafka-1                                             1/1     Running     0          2m31s   10.244.0.26   192.168.12.52   <none>           <none>
    cord-platform-kafka-2                                             1/1     Running     0          96s     10.244.2.29   192.168.12.53   <none>           <none>
    cord-platform-kibana-7459967f55-z7sk8                             1/1     Running     0          4m9s    10.244.2.18   192.168.12.53   <none>           <none>
    cord-platform-logstash-0                                          1/1     Running     0          4m9s    10.244.0.15   192.168.12.52   <none>           <none>
    cord-platform-onos-5b95b8f489-9s56b                               2/2     Running     0          4m8s    10.244.0.19   192.168.12.52   <none>           <none>
    cord-platform-prometheus-alertmanager-7df4f44f4d-tbfcl            2/2     Running     0          4m9s    10.244.2.15   192.168.12.53   <none>           <none>
    cord-platform-prometheus-kube-state-metrics-76c8565f87-wslpw      1/1     Running     0          4m9s    10.244.0.14   192.168.12.52   <none>           <none>
    cord-platform-prometheus-pushgateway-849c597464-pxhrf             1/1     Running     0          4m9s    10.244.1.26   192.168.12.51   <none>           <none>
    cord-platform-prometheus-server-555b77dcd9-brtfk                  2/2     Running     0          4m9s    10.244.2.17   192.168.12.53   <none>           <none>
    cord-platform-zookeeper-0                                         1/1     Running     0          4m9s    10.244.0.16   192.168.12.52   <none>           <none>
    cord-platform-zookeeper-1                                         1/1     Running     0          3m35s   10.244.1.31   192.168.12.51   <none>           <none>
    cord-platform-zookeeper-2                                         1/1     Running     0          2m47s   10.244.2.27   192.168.12.53   <none>           <none>
    etcd-cluster-4btz528zxt                                           1/1     Running     0          2m38s   10.244.0.25   192.168.12.52   <none>           <none>
    etcd-cluster-qpjdpn9wdl                                           1/1     Running     0          3m2s    10.244.1.35   192.168.12.51   <none>           <none>
    etcd-cluster-vg7v7rcdtn                                           1/1     Running     0          2m22s   10.244.2.28   192.168.12.53   <none>           <none>
    kpi-exporter-9b9f87bd5-7xfcw                                      1/1     Running     3          4m8s    10.244.2.16   192.168.12.53   <none>           <none>
    kpi-exporter-9b9f87bd5-gbzpm                                      1/1     Running     2          4m8s    10.244.0.17   192.168.12.52   <none>           <none>
    sadis-server-6c6f649bb4-bfg4m                                     1/1     Running     1          3m2s    10.244.2.21   192.168.12.53   <none>           <none>
    seba-base-kubernetes-tosca-loader-gsdwx                           0/1     Completed   2          3m2s    10.244.2.22   192.168.12.53   <none>           <none>
    seba-fabric-6879cd6dc9-dd2xt                                      1/1     Running     0          3m2s    10.244.2.19   192.168.12.53   <none>           <none>
    seba-fabric-crossconnect-c684c6df5-wvpjp                          1/1     Running     0          3m2s    10.244.0.21   192.168.12.52   <none>           <none>
    seba-kubernetes-bb4fcd749-z4nr8                                   1/1     Running     0          3m2s    10.244.1.32   192.168.12.51   <none>           <none>
    seba-onos-service-86697c97bf-sd2gz                                1/1     Running     0          3m2s    10.244.0.22   192.168.12.52   <none>           <none>
    seba-rcord-6975778bf6-brxvb                                       1/1     Running     0          3m2s    10.244.2.20   192.168.12.53   <none>           <none>
    seba-seba-services-tosca-loader-ddnkz                             0/1     Completed   4          3m2s    10.244.1.34   192.168.12.51   <none>           <none>
    seba-volt-f6549c677-qqfcg                                         1/1     Running     0          3m2s    10.244.1.33   192.168.12.51   <none>           <none>
    xos-chameleon-645f89cb68-5hvld                                    1/1     Running     0          4m7s    10.244.1.29   192.168.12.51   <none>           <none>
    xos-core-868868885d-x9tjx                                         1/1     Running     0          4m7s    10.244.1.30   192.168.12.51   <none>           <none>
    xos-db-7445f8dcb7-6867w                                           1/1     Running     0          4m8s    10.244.0.18   192.168.12.52   <none>           <none>
    xos-gui-858b98bc9f-pc2b5                                          1/1     Running     0          4m8s    10.244.1.27   192.168.12.51   <none>           <none>
    xos-tosca-fdbbc894b-2v264                                         1/1     Running     0          4m7s    10.244.0.20   192.168.12.52   <none>           <none>
    xos-ws-6c76444b89-kj8q7                                           1/1     Running     0          4m8s    10.244.1.28   192.168.12.51   <none>           <none>
    
    




  • No labels